H11N1M, h11n2m, h11n3m ?6-pin dip high speed logic optocouplers ?005 fairchild semiconductor corporation www.fairchildsemi.com H11N1M, h11n2m, h11n3m rev. 1.0.2 september 2009 H11N1M, h11n2m, h11n3m 6-pin dip high speed logic optocouplers features high data rate, 5mhz typical (nrz) free from latch up and oscilliation throughout voltage and temperature ranges. microprocessor compatible drive logic compatible output sinks 16ma at 0.5v maximum guaranteed on/off threshold hysteresis wide supply voltage capability, compatible with all popular logic systems high common mode transient immunity, 2000v/? minimum fast switching t r = 7.5ns typical, t f = 12ns typical underwriter laboratory (ul) recognized file #e90700 vde recognized?ile#102497 ?add option v (e.g., h11n1vm) applications logic to logic isolator programmable current level sensor line receiver?liminate noise and transient problems a.c. to ttl conversion?quare wave shaping interfaces computers with peripherals isolated power mos driver for power supplies description the h11nxm series has a high speed integrated circuit detector optically coupled to an algaas infrared emitting diode. the output incorporates a schmitt trigger, which provides hysteresis for noise immunity and pulse shap- ing. the detector circuit is optimized for simplicity of operation and utilizes an open collector output for maximum application flexibility. schematic package outlines 1 2 6 5 gnd 4 v o v cc anode cathode 3 t ruth table input output hl lh
?005 fairchild semiconductor corporation www.fairchildsemi.com H11N1M, h11n2m, h11n3m rev. 1.0.2 2 H11N1M, h11n2m, h11n3m ?6-pin dip high speed logic optocouplers absolute maximum ratings (t a = 25? unless otherwise specified.) stresses exceeding the absolute maximum ratings may damage the device. the device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. in addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. the absolute maximum ratings are stress ratings only. symbol parameters value units tot al device t stg storage temperature -40 to +150 ? t opr operating temperature -40 to +85 ? t sol lead solder temperature 260 for 10 sec ? p d t otal device power dissipation @ 25? 250 mw derate above 25? 2.94 mw/? emitter i f continuous forward current 30 ma v r reverse voltage 6 v i f (pk) forward current ?peak (1? pulse, 300 pps) 1.0 a p d led power dissipation 25? ambient 120 mw derate linearly from 25? 1.41 mw/? detector p d detector power dissipation @ 25? 150 mw derate linearly from 25? 1.76 mw/? v o v 45 allowed range 0 to 16 v v cc v 65 allowed range 0 to 16 v i o i 4 output current 50 ma
?005 fairchild semiconductor corporation www.fairchildsemi.com H11N1M, h11n2m, h11n3m rev. 1.0.2 3 H11N1M, h11n2m, h11n3m ?6-pin dip high speed logic optocouplers electrical characteristics (t a = 25? unless otherwise speci?d.) individual component characteristics t ransfer characteristics switching speed isolation characteristics *typical values at t a = 25? notes: 1. maximum i f(on) is the maximum current required to trigger the output. for example, a 3.2ma maximum trigger current would require the led to be driven at a current greater than 3.2ma to guarantee the device will turn on. a 10% guard band is recommended to account for degradation of the led over its lifetime. the maximum allowable led drive current is 30ma. 2. h11n1: r e = 910 ? , h11n2: r e = 560 ? , h11n3: r e = 240 ? symbol parameters test conditions device min. typ.* max. units emitter v f input forward voltage i f = 10ma all 1.4 2 v i f = 0.3ma 0.75 1.25 i r reverse current v r = 5v all 10 ? c j capacitance v = 0, f = 1.0mhz all 100 pf detector v cc operating voltage range all 4 15 v i cc(off) supply current i f = 0, v cc = 5v all 6 10 ma i oh output current, high i f = 0.3ma, v cc = v o = 15v all 100 ? symbol dc characteristics test conditions device min. typ.* max. units i cc(on) supply current i f = 10ma, v cc = 5v all 6.5 10 ma v ol output voltage, low r l =270 ? ,v cc =5v, i f = i f(on) max. all 0.5 v i f(on) tu r n-on threshold current r l =270 ? , v cc = 5v (1) H11N1M 0.8 3.2 ma h11n2m 2.3 5 h11n3m 4.1 10 i f(off) tu r n-off threshold current r l = 270 ? , v cc = 5v all 0.3 ma i f(off) / i f(on) hysteresis ratio r l = 270 ? , v cc = 5v all 0.65 0.95 symbol ac characteristics test conditions device min. typ.* max. units t phl propagation delay time high-to-low c = 120pf, t p = 1?, r e = (2) , figure 1 all 100 330 ns t r rise time c = 120pf, t p = 1?, r e = (2) , figure 1 all 7.5 ns t plh propagation delay time low-to-high c = 120pf, t p = 1?, r e = (2) , figure 1 all 150 330 ns t f f all time c = 120pf, t p = 1?, r e = (2) , figure 1 all 12 ns data rate all 5 mhz symbol parameters test conditions min. typ.* max. units v iso input-output isolation voltage f = 60 hz, t =1 sec. 7500 v peak c iso isolation capacitance v i-o = 0v, f = 1 mhz 0.4 0.6 pf r iso isolation resistance v i-o = ?00 vdc 10 11 ?
?005 fairchild semiconductor corporation www.fairchildsemi.com H11N1M, h11n2m, h11n3m rev. 1.0.2 4 H11N1M, h11n2m, h11n3m ?6-pin dip high speed logic optocouplers safety and insulation ratings as per iec 60747-5-2, this optocoupler is suitable for ?afe electrical insulation?only within the safety limit data. compliance with the safety ratings shall be ensured by means of protective circuits. symbol parameter min. typ. max. unit installation classi?ations per din vde 0110/1.89 ta b le 1 f or rated main voltage < 150vrms i-iv f or rated main voltage < 300vrms i-iv climatic classi?ation 55/100/21 p ollution degree (din vde 0110/1.89) 2 cti comparative tracking index 175 v pr input to output test voltage, method b, v iorm x 1.875 = v pr , 100% production test with tm = 1 sec, partial discharge < 5pc 1594 v peak input to output test voltage, method a, v iorm x 1.5 = v pr , type and sample test with tm = 60 sec, partial discharge < 5pc 1275 v peak v iorm max. working insulation voltage 850 v peak v iotm highest allowable over voltage 6000 v peak external creepage 7 mm external clearance 7 mm insulation thickness 0.5 mm rio insulation resistance at ts, v io = 500v 10 9 ?
?005 fairchild semiconductor corporation www.fairchildsemi.com H11N1M, h11n2m, h11n3m rev. 1.0.2 5 H11N1M, h11n2m, h11n3m ?6-pin dip high speed logic optocouplers t ypical performance curves c r e r l 0.1 f v in 5v v o 90% t on t r t f 10% 50% t off figure 1. switching test circuit and waveforms i f 1 2 h11n1-m v in t r = t f 0.01 s z = 50 ? 270 ? i 6 5v v o 5 6 4 0 figure 3. threshold current vs. supply voltage figure 2. transfer characteristics figure 4. threshold current vs. temperature figure 5. load current vs. output voltage 01234 i f ? input current (ma) v o - output voltage (v) 0 1 2 3 4 5 6 v cc = 5v r l = 270 ? t a = 25 c v oh v ol i f(off) i f(on) v cc ? supply voltage (v) 02468101 21416 i f - normalized threshold current 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 : hysteresis area shaded for illustration turn on threshold normalized to: turn on threshold at v cc = 5v, t a = 25 c turn off threshold t a ? temperature ( c) 01020304 0506070 normalized threshold current i f(on) , i f(off) 0.0 0.2 0.4 0.6 0.8 1.0 1.2 i f(on) i f(off) normalized to : v cc = 5v t a = 25 c v o ? output voltage, low (v) 0.0 0.2 0.4 0.6 0.8 1.0 i o - load current (ma) 1 10 100 i f = i f(on) v cc = 5v
?005 fairchild semiconductor corporation www.fairchildsemi.com H11N1M, h11n2m, h11n3m rev. 1.0.2 6 H11N1M, h11n2m, h11n3m ?6-pin dip high speed logic optocouplers t ypical performance curves (continued) figure 6. supply current vs. supply voltage figure 7. led forward voltage vs. forward current v cc ? supply voltage (v) 246810 12 14 16 i c ? supply current (ma) i f ? forward current (ma) 0 2 4 6 8 10 12 off state i f = 0 on state i f = 10ma t a = 85 c t a = -25 c t a = 25 c v f ? forward voltage (v) 1.0 1.2 1.4 1.6 1.8 2.0 1 10 100 t a = 85 c t a = -25 c t a = 25 c
?005 fairchild semiconductor corporation www.fairchildsemi.com H11N1M, h11n2m, h11n3m rev. 1.0.2 7 H11N1M, h11n2m, h11n3m ?6-pin dip high speed logic optocouplers package dimensions 8.13?.89 6.10?.60 pin 1 64 13 0.25?.36 5.08 (max.) 3.28?.53 0.38 (min.) 2.54?.81 2.54 (bsc) (0.86) 0.41?.51 1.02?.78 0.76?.14 8.13?.89 6.10?.60 pin 1 64 13 0.25?.36 5.08 (max.) 3.28?.53 0.38 (min.) 2.54?.81 2.54 (bsc) (0.86) 0.41?.51 1.02?.78 0.76?.14 7.62 (typ.) 15?(typ.) 0.20?.30 0.20?.30 10.16?0.80 through hole 0.4" lead spacing surface mount rcommended pad layout (1.78) (2.54) (1.52) (7.49) (10.54) (0.76) 8.13?.89 note: all dimensions in mm. 6.10?.60 8.43?.90 pin 1 64 13 0.25?.36 2.54 (bsc) (0.86) 0.41?.51 1.02?.78 0.76?.14 0.38 (min.) 3.28?.53 5.08 (max.) 0.20?.30 0.16?.88 (8.13)
?005 fairchild semiconductor corporation www.fairchildsemi.com H11N1M, h11n2m, h11n3m rev. 1.0.2 8 H11N1M, h11n2m, h11n3m ?6-pin dip high speed logic optocouplers ordering information marking information option order entry identi?er (example) description no option H11N1M standard through hole device s h11n1sm surface mount lead bend sr2 h11n1sr2m surface mount; tape and reel t h11n1tm 0.4" lead spacing v h11n1vm vde 0884 tv h11n1tvm vde 0884, 0.4" lead spacing sv h11n1svm vde 0884, surface mount sr2v h11n1sr2vm vde 0884, surface mount, tape and reel h11n1 1 2 6 4 3 5 *note ?parts that do not have the ??option (see definition 3 above) that are marked with date code ?25?or earlier are marked in portrait format. de?nitions 1f airchild logo 2d e vice number 3 vde mark (note: only appears on parts ordered with vde option ?see order entry table) 4 one digit year code, e.g., ? 5t wo digit work week ranging from ?1 to ?3 6 assembly package code v x yy q
?005 fairchild semiconductor corporation www.fairchildsemi.com H11N1M, h11n2m, h11n3m rev. 1.0.2 9 H11N1M, h11n2m, h11n3m ?6-pin dip high speed logic optocouplers tape dimensions note: all dimensions are in millimeters. reflow soldering profile 4.0 0.1 1.5 min user direction of feed 2.0 0.05 1.75 0.10 11.5 1.0 24.0 0.3 12.0 0.1 0.30 0.05 21.0 0.1 4.5 0.20 0.1 max 10.1 0.20 9.1 0.20 1.5 0.1/-0 300 280 260 240 220 200 180 160 140 120 100 80 60 40 20 0 c time (s) 0 60 180 120 270 260 c >245 c = 42 sec time above 183 c = 90 sec 360 1.822 c/sec ramp up rate 33 sec
?005 fairchild semiconductor corporation www.fairchildsemi.com H11N1M, h11n2m, h11n3m rev. 1.0.2 10 tradem arks th e following includes registered and unregistered trademarks and service marks, owned by fairchild semiconductor and/or its global subsidiaries ,and is not in tended to be an exhaustive list of all such trademarks. auto-spm build it now coreplus corepower crossvolt ctl current transfer logic ecospark e fficentmax ezswitch * * fair child fairchild semiconductor fa ct quiet series fact f ast fa stvcore fetbench flashwriter * fps f-pfs frfet global power resource sm green fps green fps e-series g max gto in tellimax isoplanar me gabuck mi crocoupler microfet mi cropak m illerdrive moti onmax mo tion-spm optologic op toplanar pdp spm powe r-spm po we rtrench powerxs pr ogrammable active droop qfet qs quiet series r apidconfigure saving our world, 1mw/w/kw at a time sm artmax smart start spm stealth s uperfet sup ersot -3 s upersot -6 s upersot -8 s upremos syncfet sy nc-lock * th ep ower franchise ti nyboost tinybuck ti nylogic tinyopto tinypower tinypwm tinywire trifault detect t ruecurrent * serdes uhc ultra frfet unifet vcx vi sualmax xs *t rademarks of system general corporation, used under license by fairchild semiconductor. disclaimer fa i rchild semiconductor reserves the right to make changes without further notice to any products herein to improve reliability, function, or design. fairchild does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights, nor the rights of others. these specifications do not expand the terms of fairchild? worldwide terms and conditions, specifically the warranty therein, which covers t hese products. li fe support policy fa i rchild? products are not authorized for use as critical components in life support devices or systems without the express written approval of fairchild semiconductor corporation. as used herein: 1. life support devices or systems are devices or systems which, (a) are in tended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance wi th instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. a critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. an ti -counterfeiting policy fairchild semiconductor corporation's anti-counterfeiting policy. fairchild's anti-counterfeiting policy is also stated on our external websi te, www.fairchildsemi.com, under sales support. c ounterfeiting of semiconductor parts is a growing problem in the industry. all manufacturers of semiconductor products are experiencing counterf eiting of their parts. cu stomers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, faile da pplications, and increased cost of production and manufacturing delays. fairchild is taking strong measures to protect ourselves and our customers from the proli feration of counterfeit parts. fairchild strongly encourages customers to purchase fairchild parts either directly from fairchild or from authorized fairchi ld dist ributors who are lis ted by country on our web page cited above. products customers buy either from fairchild directly or from authorized fairchild distributors are ge nuine parts, have full traceability, meet fairchild's quality standards for handling and storage and provide access to fairchild's full range of up-to-date technica land product information. fairchild and our authorized distributors will stand behind all warranties and will appropriately address any warranty issues that may arise. fairc hild will not provide any warranty coverage or other assistance for parts bought from unauthorized sources. fairchild is committed to combat this global problem and encou rage our customers to do their part in stopping this practice by buying direct or from authorized distributors. product status definitions defi nition of terms da tasheet identification product st atus definition ad vance information formative / in design datasheet contains the design specifi cations for product development. s pecifications may change in any manner without notice. pr eliminary datasheet contains preliminary data; supplementary data will be published at a later date. fairchild se mi conductor reserves the right to make changes at any time without notice to improve design. no i dentification needed full production datasheet contains final specifications. fairchi ld semiconductor reserves the right to make changes at any time without notice to improve the design. obsolete not in production datasheet contains specifications on a product that is discontinued by fairchild semiconductor. th e datasheet is for reference information only. rev. i40 first production H11N1M, h11n2m, h11n3m ?6-pin dip high speed logic optocouplers
|
